Loading

Capsule Weight Uniformity Testing: Limits, Method and Free Checker

White empty hard gelatin capsules

Weight uniformity is one of the simplest and most important quality tests for filled capsules. If capsule fill weights vary too much, patients receive different doses from capsule to capsule. This guide explains how the uniformity of weight test works for hard gelatin capsules, the pharmacopoeia limits, what causes failures, and how the empty capsule itself plays a part.

The short answer

Weigh 20 filled capsules and calculate the average. Under the IP and BP, if the average is below 300 mg, no more than two capsules may differ from the average by more than 10 percent, and none by more than 20 percent. At 300 mg or more, the limits are 7.5 and 15 percent.

Capsule weight uniformity checker

This checker applies the uniformity of weight limits for capsules in the IP and BP. It is a guide, not a substitute for your validated QC procedure.

Uniformity of weight limits for capsules

IP and BP uniformity of weight limits for hard capsules (20 capsules tested)
Average weightMaximum deviation (up to 2 capsules)No capsule may exceed
Less than 300 mg±10%±20%
300 mg or more±7.5%±15%

The USP approaches this through Uniformity of Dosage Units (chapter <905>), which allows weight variation in place of content uniformity for capsules where the drug makes up a large enough share of the fill. Always follow the pharmacopoeia that applies to your market.

How to perform the test

  1. Take 20 capsules at random from the batch.
  2. Weigh each intact capsule individually (gross weight).
  3. For a more accurate check, open each capsule, empty it completely and weigh the shell; the fill weight is the difference.
  4. Calculate the average weight and the percentage deviation of each capsule.
  5. Compare the results with the limits above.

The role of the empty capsule

Gross weight includes the shell, so variation in empty capsule weight adds to the total. Universe Capsules controls empty capsule weight to within ±7 percent of the nominal weight for each size. For a size 0 capsule, which weighs about 99 mg, that is only a few milligrams. See our size chart for every size.

Common causes of weight variation

  • Poor powder flow: cohesive or fluffy powders fill unevenly. Granulation or a glidant usually helps.
  • Wrong capsule size: an over-full or under-full capsule fills inconsistently. Use our capsule size calculator.
  • Machine settings: tamping force, dosing disc height and powder bed depth all affect fill weight.
  • Capsule moisture: shells that are too dry or too humid may split or not open cleanly. See how to store empty capsules.
  • Segregation: blends with very different particle sizes separate in the hopper.

For machine problems, see capsule filling problems and solutions, and for the full picture of capsule QC, read why quality control matters.

Frequently asked questions

What is the weight variation limit for capsules?

Under the IP and BP, for capsules with an average weight below 300 mg, no more than two of 20 capsules may deviate from the average by more than 10 percent and none by more than 20 percent. At 300 mg or more, the limits are 7.5 and 15 percent.

How many capsules are used for the uniformity of weight test?

20 capsules taken at random from the batch.

Does empty capsule weight affect the test?

Yes. Gross weight includes the shell, so consistent empty capsule weight helps. Universe Capsules controls empty capsule weight within ±7 percent.

How can I reduce capsule weight variation?

Improve powder flow, choose the right capsule size, set tamping and dosing correctly, and store capsules at the right humidity.

Consistent capsules, consistent doses

Ask for samples of our empty hard gelatin capsules and a certificate of analysis.

Request samples

Leave a Reply

Your email address will not be published. Required fields are marked *

Enquiry Here

Give us a call or fill in the form below and we'll contact you. We endeavor to answer all inquiries within 24 hours on business days.